| Machine ID: |
77 |
| Machine Name: |
|
| Location: |
|
Default Setup (in seconds): |
|
| Default Efficiency: |
|
| Cost per hour Setup (in dollars): |
|
| Cost per hour Run (in dollars): |
|
| Work Center: |
|
| Show materials on display: |
|
| Require Cycle Time: |
|
| Custom right hand: |
|
| Custom bottom hand: |
|
| Inline hand: |
|
| Inline position: |
|
| Quick pick seconds field: |
|
| Number of people: |
|
| Set inactive: |
|
| Output: |
|
|
|
| Notes: |
|
|
Setting up the machine questions
After editing any of the question below, you will need to to press the to refresh the content in the fields area.
|
|
After editing any of the question above, you will need to to press the to refresh the content in the fields area.
|
|
|
Fields:
|
$field['field_1_name']="Load Time";
$field['field_1_default']="5";
$field['field_2_name']="Part flips (qty)";
$field['field_2_default']="0";
$field['field_2_time']="7";
$field['field_3_name']="Vice clamps (qty)";
$field['field_3_default']="1";
$field['field_3_time']="3";
$field['field_4_name']="Holes to center drill (qty)";
$field['field_4_default']="";
$field['field_5_name']="Holes to drill/csink (qty)";
$field['field_5_default']="";
$field['field_6_name']="Holes to tap/ream (qty)";
$field['field_6_default']="";
$field['field_7_name']="Seconds per hole (center drilling/csink)";
$field['field_7_default']="5";
$field['field_8_name']="Seconds per hole (drilling)";
$field['field_8_default']="8";
$field['field_9_name']="Seconds per hole (tapping/reaming)";
$field['field_9_default']="10";
$field['field_10_name']="Inches to turn, tool #1";
$field['field_10_default']="";
$field['field_10_convert']="yes";
$field['field_11_name']="IPM for turning, tool #1";
$field['field_12_name']="Inches to turn, tool #2";
$field['field_12_default']="";
$field['field_12_convert']="yes";
$field['field_13_name']="IPM for turning, tool #2";
$field['field_14_name']="Inches to turn, tool #3";
$field['field_14_default']="";
$field['field_14_convert']="yes";
$field['field_15_name']="IPM for turning, tool #3";
$field['field_16_name']="Inches to turn, tool #4";
$field['field_16_default']="";
$field['field_16_convert']="yes";
$field['field_17_name']="IPM for turning, tool #4";
$field['field_18_name']="Inches to turn, tool #5";
$field['field_18_default']="";
$field['field_18_convert']="yes";
$field['field_19_name']="IPM for turning, tool #5";
$field['field_20_name']="Inches to turn, tool #6";
$field['field_20_default']="";
$field['field_20_convert']="yes";
$field['field_21_name']="IPM for turning, tool #6";
$field['field_22_name']="Inches to turn, tool #7";
$field['field_22_default']="";
$field['field_22_convert']="yes";
$field['field_23_name']="IPM for turning, tool #7";
$field['field_24_name']="Inches to part";
$field['field_24_default']="";
$field['field_24_convert']="yes";
$field['field_25_name']="IPM for parting";
$field['field_26_name']="Tool changes req'd (qty)";
$field['field_26_default']="";
$field['field_26_time']="5";
|
Extras:
|
|
Evaluations:
|
(float)$eval['load']=(float)$_POST['1'];
(float)$eval['part flips']=((float)$_POST['2']*(float)$field['field_2_time']);
(float)$eval['vice clamping time']=((float)$_POST['3']*(float)$field['field_3_time']);
(float)$eval['center drilling time']=((float)$_POST['4']*(float)$_POST['7']);
(float)$eval['drilling time']=((float)$_POST['5']*(float)$_POST['8']);
(float)$eval['tapping time']=((float)$_POST['6']*(float)$_POST['9']);
if((float)$_POST['11']){(float)$eval['tool one']=(((float)$_POST['10']/(float)$_POST['11'])*'60');}
if((float)$_POST['13']){(float)$eval['tool two']=(((float)$_POST['12']/(float)$_POST['13'])*'60');}
if((float)$_POST['15']){(float)$eval['tool three']=(((float)$_POST['14']/(float)$_POST['15'])*'60');}
if((float)$_POST['17']){(float)$eval['tool four']=(((float)$_POST['16']/(float)$_POST['17'])*'60');}
if((float)$_POST['19']){(float)$eval['tool five']=(((float)$_POST['18']/(float)$_POST['19'])*'60');}
if((float)$_POST['21']){(float)$eval['tool six']=(((float)$_POST['20']/(float)$_POST['21'])*'60');}
if((float)$_POST['23']){(float)$eval['tool seven']=(((float)$_POST['22']/(float)$_POST['23'])*'60');}
if((float)$_POST['25']){(float)$eval['parting']=(((float)$_POST['24']/(float)$_POST['25'])*'60');}
(float)$eval['tool change time']=((float)$_POST['26']*(float)$field['field_26_time']);
(float)$totals['part seconds each']=(
(float)$eval['load']+
(float)$eval['part flips']+
(float)$eval['vice clamping time']+
(float)$eval['center drilling time']+
(float)$eval['drilling time']+
(float)$eval['tapping time']+
(float)$eval['tool one']+
(float)$eval['tool two']+
(float)$eval['tool three']+
(float)$eval['tool four']+
(float)$eval['tool five']+
(float)$eval['tool six']+
(float)$eval['tool seven']+
(float)$eval['parting']+
(float)$eval['tool change time']);
|
|
|
