| Machine ID: |
76 |
| Machine Name: |
|
| Location: |
|
Default Setup (in seconds): |
|
| Default Efficiency: |
|
| Cost per hour Setup (in dollars): |
|
| Cost per hour Run (in dollars): |
|
| Work Center: |
|
| Show materials on display: |
|
| Require Cycle Time: |
|
| Custom right hand: |
|
| Custom bottom hand: |
|
| Inline hand: |
|
| Inline position: |
|
| Quick pick seconds field: |
|
| Number of people: |
|
| Set inactive: |
|
| Output: |
|
|
|
| Notes: |
|
|
Setting up the machine questions
After editing any of the question below, you will need to to press the to refresh the content in the fields area.
|
|
After editing any of the question above, you will need to to press the to refresh the content in the fields area.
|
|
|
Fields:
|
$field['field_1_name']="Load Time";
$field['field_1_default']="10";
$field['field_2_name']="Edge finding needed (qty)";
$field['field_2_default']="0";
$field['field_2_time']="10";
$field['field_3_name']="Vice clamps (qty)";
$field['field_3_default']="1";
$field['field_3_time']="5";
$field['field_4_name']="Holes to center drill/csink (qty)";
$field['field_4_default']="";
$field['field_5_name']="Holes to drill (qty)";
$field['field_5_default']="";
$field['field_6_name']="Holes to tap/ream (qty)";
$field['field_6_default']="";
$field['field_15_name']="Inches to plunge (inches)";
$field['field_15_default']="";
$field['field_16_name']="IPM for plunging";
$field['field_16_default']="";
$field['field_7_name']="Inches to mill (inches)";
$field['field_7_default']="";
$field['field_7_convert']="yes";
$field['field_8_name']="IPM for milling";
$field['field_27_name']="2nd Inches to mill (inches)";
$field['field_27_default']="";
$field['field_27_convert']="yes";
$field['field_28_name']="2nd IPM for milling";
$field['field_29_name']="3rd Inches to mill (inches)";
$field['field_29_default']="";
$field['field_29_convert']="yes";
$field['field_30_name']="3rd IPM for milling";
$field['field_9_name']="Seconds per hole (center drilling/csink)";
$field['field_9_default']="5";
$field['field_10_name']="Seconds per hole (drilling)";
$field['field_10_default']="8";
$field['field_11_name']="Seconds per hole (tapping/reaming)";
$field['field_11_default']="10";
$field['field_12_name']="Tool changes req'd (qty)";
$field['field_12_default']="";
$field['field_12_time']="3";
$field['field_13_name']="Indexing req'd (qty)";
$field['field_13_default']="";
$field['field_13_time']="5";
$field['field_14_name']="Total Rapid in Inches";
$field['field_14_default']="";
|
Extras:
|
$field['order']=array(1,2,3,4,5,6,7,8,27,28,29,30,9,10,11,12,13,14,15,16);
|
Evaluations:
|
(float)$eval['load']=(float)$_POST['1'];
(float)$eval['edge finding time']=((float)$_POST['2']*(float)$field['field_2_time']);
(float)$eval['vice clamping time']=((float)$_POST['3']*(float)$field['field_3_time']);
(float)$eval['center drilling time']=((float)$_POST['4']*(float)$_POST['9']);
(float)$eval['drilling time']=((float)$_POST['5']*(float)$_POST['10']);
(float)$eval['tapping time']=((float)$_POST['6']*(float)$_POST['11']);
if((float)$_POST['8']){(float)$eval['1st milling time']=(((float)$_POST['7']/(float)$_POST['8'])*'60');}
if((float)$_POST['28']){(float)$eval['2nd milling time']=(((float)$_POST['27']/(float)$_POST['28'])*'60');}
if((float)$_POST['30']){(float)$eval['3rd milling time']=(((float)$_POST['29']/(float)$_POST['30'])*'60');}
(float)$eval['milling time']=((float)$eval['1st milling time']+(float)$eval['2nd milling time']+(float)$eval['3rd milling time']);
if((float)$_POST['16']){(float)$eval['plunge time']=(((float)$_POST['15']/(float)$_POST['16'])*'60');}
(float)$eval['tool change time']=((float)$_POST['12']*(float)$field['field_12_time']);
(float)$eval['index time']=((float)$_POST['13']*(float)$field['field_13_time']);
(float)$eval['rapid time']=(((float)$_POST['14']/'700')*'60');
(float)$totals['part seconds each']=(
(float)$eval['load']+
(float)$eval['edge finding time']+
(float)$eval['vice clamping time']+
(float)$eval['center drilling time']+
(float)$eval['drilling time']+
(float)$eval['tapping time']+
(float)$eval['milling time']+
(float)$eval['plunge time']+
(float)$eval['rapid time']+
(float)$eval['index time']+
(float)$eval['tool change time']);
|
|
|
